>Home>Products>

chloride and sulphate content test of aggregate:

Permissible Levels of Chlorides and Sulfates in Aggregate ...

Feb 01, 1996  Q. We're designing a concrete structure in Egypt, and I received test results for the aggregate to be used in the concrete. The report lists chloride and sulfate content, but I don't know how to evaluate these numbers because ASTM C 33, "Standard Specification for Concrete Aggregates," doesn't give limits for them.

Read More
Discussion and experiments on the limits of chloride ...

Jan 20, 2018  Discussion and experiments on the limits of chloride, sulphate and shell content in marine fine aggregates for concrete. ... 0.06 for 95% of test results, with no result greater than 0.08. ... If the chloride content in aggregates is less than 0.01%, then this 0.01% is suggested to be used to calculate the total chloride content in concrete.

Read More
The combined effect of chlorides and sulphates present in ...

Nov 01, 1988  The combined effect of sulphates present in aggregates and high levels of chloride ions in the mixing water on some properties of concrete was studied. Different amounts of sulphates in sand (0.38, 0.50, 0.75 and 1.0% SO 3) with chloride contents in water (50, 750, 1000, 3000 and 6000 p.p.m. as Cl −) were used. The compressive strength was lower for concrete with higher sulphate contents at

Read More
DETERMINING CHLORIDE AND SULFATE CONTENTS IN SOIL

DETERMINING CHLORIDE AND SULFATE CONTENTS IN SOIL TXDOT DESIGNATION: TEX-620-J CONSTRUCTION DIVISION 4 – 11 LAST REVIEWED: OCTOBER 2014 6.1.2 To prepare a 1.0-ppm standard, use a 1-mL pipette to transfer a 1-mL aliquot of the anion standard solution into a 100-mL volumetric flask, and dilute to the mark.

Read More
chloride and sulphate content test of aggregate

sulfate sulphate content aggregates washing - 17/12/2012 sulfate sulphate content aggregates washing – Grinding Mill China. sulfate contents in fine aggregate fo concrete Aggregate mining and washing stone; Aggregate mining in vietnam The report lists chloride and sulfate content

Read More
Standard Test Method for Water-Extractable Chloride in ...

4.1 Water-extractable chloride, when present in sufficient amount, has a potential to initiate or accelerate corrosion of metals, such as steel, embedded in or contacting a cementitious system, such as mortar, grout, or concrete. This test method is applicable when aggregates contain a high background of naturally occurring chloride (see ACI 222.1–96 ).

Read More
Sulphate Content Testing Of Aggregate

Sulphate Content Testing Of Aggregate. Sulphate attack on concrete is a chemical process where sulphate ions attack components of cement paste.Fly ash, aggregate, and admixtures.Portland cement might be over-sulphated.Presence of natural gypsum in the aggregate.Chemical process of sulphate attack.The sulphate ion hydrated calcium aluminate andor the calcium.

Read More
DETERMINATION OF SOLUBLE SULPHATE CONTENT IN SOIL (IS

May 07, 2015  Determination of Soluble Sulphate Content Purpose Sodium sulphate is present in some soils. The salt is easily hydrated and dehydrated under the influence of climatic changes. There are enormous volume changes during this process of hydration and dehydration, which influence the engineering properties of soils. Procedure Take the soil sample in a state in which []

Read More
(PDF) Analysis of total chloride content in concrete

Dec 31, 2015  Total chloride in the actual concrete mixtures: (A) water chloride content is 250 ppm, (B) water chloride content is 750 ppm, and (C) water chloride content is 1250 ppm.

Read More
IS 6925 (1973): Specification for Methods of Test for ...

with the methods of test for determination of water content in concrete admixtures. 0.3 In reporting the result of a test or analysis made in this standard, if the final value, observed or calculated, off, it shall be done in accordance with IS :2-1960t. -,’ 1. SCOPE soluble chlorid: accordance with

Read More
Discussion and experiments on the limits of chloride ...

Jan 20, 2018  Discussion and experiments on the limits of chloride, sulphate and shell content in marine fine aggregates for concrete. ... 0.06 for 95% of test results, with no result greater than 0.08. ... If the chloride content in aggregates is less than 0.01%, then this 0.01% is suggested to be used to calculate the total chloride content in concrete.

Read More
QUANTAB CHLORIDE AND SULFATE CONTENT INSTANT TEST STRIPS ...

Type 1176 titration range 0.05% to 0.1% (300 to 6000ppm) NaCl. Pack of 40. A qualitative or semi-quantitative test is recommended for determining sulfate ions in aqueous solutions. Sulfate test strips are convenient measuring devices for sulfate content. AG 0109 Sulfate Test Strips detection range 200 to 900 mg/l. Pack of 100.

Read More
Aggregate Testing Admaterials

Since beginning, Admaterials has provided imported aggregate testing for the following tests as required by BCA. Petrographic Examination (ASTM C295), Alkali Silica Reactivity–Mortar Bar Method (ASTM C1260), Water Soluble Chloride Content (EN 1744-1, Clause 7), Acid Soluble Sulphate Content (EN 1744-1, Clause 12)

Read More
Chemical Testing (Aggregate) — Celtest

Oct 19, 2018  Laboratory Testing, Aggregate Alex Moore 19 October 2018 Aggregate Chemical Testing, BS 812, BS EN 1744-1, Chloride, EN 1367-2, Fulvo Acid, Humus Content, Laboratory, Lignite Content, Organic Contaminators, Sulphate, Sulphides

Read More
Chloride limits in the ACI 318 building code requirements

A new test, the Soxhlet method (ACI 222.1), has been de-veloped to test these aggregates or to test concrete made with these aggregates. This test uses chunks of concrete or aggregate instead of crushed and powdered material. The chunks or pieces are treated with boiling water, which is then tested for chloride content. So far, the test appears

Read More
Determining Chloride Content of Concrete The Virginia ...

ACI 318-19 section 26.4.2.2 provides two alternatives for determining the chloride ion content of concrete: (1) calculate the chloride ion content based upon the total chloride ion content of the concrete materials and mix proportions, or (2) test for water-soluble chloride ion content in accordance with ASTM C1218.

Read More
Chemical Requirement of Aggregates as per European ...

The water-soluble chloride ion content of aggregates for concrete shall be determined in accordance with EN 1744-1:1998, clause 7, and shall, on request, be declared by the producer. If the water-soluble chloride ion content of the combined aggregate is known to be 0.01 % or lower (e.g., for extracted from most inland quarries), this value can ...

Read More
Aggregates in Saudi Arabia: a survey of their properties ...

The present paper presents some typical results obtained, such as water absorption, grading, dust content, chloride and sulphate content and soundness. It focuses attention on limits, set by some international standards, regarding the acceptability of aggregates provided for concrete.

Read More
Aggregates for Concrete - CEDD

Construction Standard CS3:2013 . Aggregates for Concrete . 香港特別行政區政府 The Government of the Hong Kong Special Administrative Region

Read More
Sulfate in concrete

Sulfate in concrete Excessive amounts of mobile sulfate, derived from aggregates or other constituents in concrete, can cause disruption due to expansion. BS 8110 part 1 Structural use of concrete, 1985, had a limit of 4% by mass of cement based on the total acid soluble sulfate method expressed as SO 3 (clauses 6.2.5.3).

Read More
(PDF) Specification for aggregates from natural sources ...

The carbonate content shall be expressed as equivalent calcium carbonate content in accordance with the recommendations in BRE Special Digest 1. 5 Grading 5.1 Coarse aggregate When determined in accordance with BS 812-103.1 using test sieves of the sizes given in Table 3, complying with BS 410, full tolerance, the grading of the coarse ...

Read More
Analysis of total chloride content in concrete

Round-Robin Test on chloride analysis in concrete, car-ried out by the Technical Committee TC 178-TMC. A Analysis of total chloride content in concrete RILEM TC 178-TMC: ‘TESTING AND MODELLING CHLORIDE PENETRATION IN CONCRETE’ RILEM TECHNICAL COMMITTEES The text presented herafter is a draft for general consideration.

Read More
Aggregate Testing Definition, Flakiness Elongation Index

This test method covers chemical determination of the potential reactivity of an aggregate with alkalis in Portland cement concrete, as indicated by the amount of reaction during 24 hours at 80°C between 1N sodium hydroxide solution and aggregate that has been crushed and sieved to pass a 300µm sieve and retained on a 150µm sieve.

Read More
Chloride Testing Sandberg

Chloride testing is mainly carried out on reinforced concrete using test methods given in BS 1881. Chloride can be present in the concrete either as added calcium chloride used to accelerate the setting time of the concrete or as a contaminant of the aggregate.

Read More
QUANTAB CHLORIDE AND SULFATE CONTENT INSTANT TEST STRIPS ...

Type 1176 titration range 0.05% to 0.1% (300 to 6000ppm) NaCl. Pack of 40. A qualitative or semi-quantitative test is recommended for determining sulfate ions in aqueous solutions. Sulfate test strips are convenient measuring devices for sulfate content. AG 0109 Sulfate Test Strips detection range 200 to 900 mg/l. Pack of 100.

Read More
Effect of Chloride and Sulfate Contamination in Soils on ...

to both sulfate and chloride attack. In such situations, use of Type V cement, though providing adequate protection against sulfate attack, fails to remove free chlorides from concrete. To inhibit reinforcement corrosion, cement with a high tri­ calcium aluminate (C 3A) content should be used (4). Rash­

Read More
Types of Testing for Aggregates - Structural Guide

TESTING OF AGGREGATE CRUSHING VALUE. Aggregate crushing value is an indicator of the crushing resistance of the aggregates when a compressive load is increased. It is tested in accordance with BS 812:110, 1990 and aggregate passing a 14mm test sieve and retained on 10mm sieve are considered for the testing. The allowable range is 17- 41.

Read More
Testing of industrial products - Aggregates for construction

The results of the experiments show that the reproducibility of the test is not good enough for it to be used as the reference method for the determination of the acid-sulfate content of aggregates. This is when the determinations are to be used to check that the aggregate complies with a specification limit around 0.2% to 1% SO 3 .

Read More
Aggregate Testing Definition, Flakiness Elongation Index

This test method covers chemical determination of the potential reactivity of an aggregate with alkalis in Portland cement concrete, as indicated by the amount of reaction during 24 hours at 80°C between 1N sodium hydroxide solution and aggregate that has been crushed and sieved to pass a 300µm sieve and retained on a 150µm sieve.

Read More
Chemical Requirement of Aggregates as per European ...

The water-soluble chloride ion content of aggregates for concrete shall be determined in accordance with EN 1744-1:1998, clause 7, and shall, on request, be declared by the producer. If the water-soluble chloride ion content of the combined aggregate is known to be 0.01 % or lower (e.g., for extracted from most inland quarries), this value can ...

Read More
Test for Aggregates for Concrete - Aggregate Soundness ...

Jan 14, 2021  The most common soundness test involves repeatedly submerging an aggregate sample in a saturated solution of sodium or magnesium sulphate. The disintegration of aggregates is recorded. Apparatus for Determining Aggregate Soundness Test Sieves for fine aggregate : 150, 300, 600 micron and 1.18, 2.36, 4.00, 4.75 mm

Read More
Aggregates in Saudi Arabia: a survey of their properties ...

The present paper presents some typical results obtained, such as water absorption, grading, dust content, chloride and sulphate content and soundness. It focuses attention on limits, set by some international standards, regarding the acceptability of aggregates provided for concrete.

Read More
(PDF) Specification for aggregates from natural sources ...

The carbonate content shall be expressed as equivalent calcium carbonate content in accordance with the recommendations in BRE Special Digest 1. 5 Grading 5.1 Coarse aggregate When determined in accordance with BS 812-103.1 using test sieves of the sizes given in Table 3, complying with BS 410, full tolerance, the grading of the coarse ...

Read More
Sulfate in concrete

Sulfate in concrete Excessive amounts of mobile sulfate, derived from aggregates or other constituents in concrete, can cause disruption due to expansion. BS 8110 part 1 Structural use of concrete, 1985, had a limit of 4% by mass of cement based on the total acid soluble sulfate method expressed as SO 3 (clauses 6.2.5.3).

Read More
A S Laboratories Chlorides - Chloride Testing

The water-soluble version of this test is known as Procedure A. The acid-soluble version, or total chloride version, is known as Procedure B. ASTM C 1524 This test method is a way to test aggregate for chlorides in a different water-soluble procedure. It is normally used when an aggregate

Read More
What are the various durability tests on concrete? - Quora

The ability of cement concrete to resist weathering action,chemical attack and any process that can deteriorate its condition is known as durablity of concrete.The concrete that retains its original form,quality serviceablity inspite of any kind...

Read More
Four-years carbonation and chloride induced steel ...

Feb 28, 2018  From the test results, the use of magnesium sulfate contaminated aggregate in concrete increases the steel weight loss compared with sodium and calcium sulfate contaminated aggregate. For example, at 1.0% sulfate content, the steel weight loss of magnesium sulfate contaminated aggregate concrete yields 26.3% and 13.5% higher than those of ...

Read More
Determination of Chloride and Sulfate in Water and Soil

2 System Selection In this study, the determination of chloride and sulfate in soil and water samples is demonstrated using two systems: an integrated Thermo Scientific ™ Dionex ICS-2100 system that operates as a Reagent-Free ™ IC (RFIC ) system and a Dionex ICS-5000+ HPIC™ system that is capable of supporting high-pressure IC and is also a RFIC

Read More